Zoned Vacuum Control
The bed is split into four independent zones, so holding a single 60 × 40 cm sheet does not require pulling vacuum across the whole table. Pump load and power draw scale with the job, not the machine.
MK-1612 imagery in production
Cutting Systems & Plotters
Maven MK-1612
Knife, crease and router in one head, from sheet to finished part in one stop
- Cutting Area
- 1600 × 1200 mm
- Max Cutting Speed
- 1000 mm/s
- Cutting Force
- 200 N
- Cutting Accuracy
- 0.05 mm
Price on request
01 — OVERVIEW
The MK-1612 gathers post-print finishing onto one 1600 × 1200 mm vacuum bed. Three of the tangential knife, oscillating knife, creasing and routing modules sit in the head at once, and a tool change needs no recalibration. The carriage runs to 1000 mm/s with acceleration up to 1 G, down-force reaches 200 N, repeatability is ± 0.05 mm. Four independent vacuum zones hold a single sheet at the same pump load as a full bed, and optical mark reading carries print-side drift into the cut path.
MavenSight Optical Mark Reading
A head-mounted camera reads the registration marks in the print and carries material stretch into the cut path as X/Y scaling. On banner or vinyl that has been through eco-solvent heaters, this is the only real answer to contour drift.
TriTool Three-Module Head
Any three of the tangential knife, oscillating knife, creasing, routing and V-cut modules stay fitted at the same time. Single-point fastening makes a module change a matter of minutes and preserves the tool origin.
MavenPanel Continuous Feed
With advance clamps and the conveyor option, work longer than the bed is cut panel by panel up to a total job length of 50 m. A tall totem body is finished as one file instead of being split and joined.
02 — TECHNICAL DATA
Specifications
| Mode | Pass | Speed |
|---|---|---|
| Cutting — kiss-cut vinyl | 1 | 40–55 m²/h |
| Cutting — tangential knife | 1 | 22–30 m²/h |
| Cutting — oscillating tool | 1 | 10–16 m²/h |
| Printing | |
|---|---|
| Max Media Width | 1650 mm |
| Mechanical | |
| Table / Bed | Bölgesel vakumlu kesim tablası |
| Vacuum Zones | 4 zones |
| Media Feed System | Kıskaçlı malzeme ilerletme ve konveyör opsiyonu; panelli kesimde 50 m'ye kadar iş boyu |
| Cutting | |
| Cutting Area | 1600 × 1200 mm |
| Max Cutting Speed | 1000 mm/s — acceleration up to 1 G |
| Cutting Force | 200 N |
| Cutting Accuracy | 0.05 mm — ± repeatability |
| Tool Modules | Tek noktadan bağlantılı çok modüllü kafa · aynı anda 3 takım |
| Cuttable Materials | Yapışkanlı folyo · branda · reflektif folyo · manyetik levha · dekota · fotoblok · mukavva · oluklu mukavva · MDF · alüminyum kompozit · tekstil |
| Cut File Formats | AI · EPS · PDF · DXF · PLT (HPGL) |
| Power & Environment | |
| Power Supply | AC 380–400 V + N, 50 Hz, 3 faz (3 × 230 V 50 Hz ve 3 × 208 V 60 Hz varyantları) |
| Power Consumption | 1.3 kW — vacuum pump; 1.75 kW at 60 Hz |
| Current | 20 A — maximum on a 3 × 400 V + N supply |
| Operating Environment | 18–30 °C / %35–65 BN |
| Software & Connectivity | |
| RIP Software | ONYX · Caldera · SAi Flexi |
| Interface | Gigabit Ethernet · USB |
| Physical | |
| Dimensions (W × D × H) | 2470 × 2200 × 1100 mm |
| Required Floor Area | 16 m2 |
Compatible Substrates
- Vinyl
- Foam PVC
- PVC
- Aluminium Composite
- Foam Board
- Paper
- Textile
- Leather
03 — INSTALLATION
Installation Requirements
We publish this before the sale. A machine that will not fit through the door, or a supply that cannot carry it, is the most expensive surprise there is.
- Power
- Three-phase (380 V)
- Floor area
- 16 m²
- Ceiling height
- 2.8 m
- Crated size
- 2700 × 2400 × 1350 mm
- Ventilation
- Not required
- Compressed air
- 6 bar, 100 L/dk
Not included in the price
- Freight and insurance
- Forklift or pallet-truck unloading
- Electrical infrastructure and three-phase panel
- Compressed air line
- Dust extraction unit for the routing module
- Starter set of blades and cutting underlay
04 — QUESTIONS
Frequently Asked Questions
What is the MK-1612 the right machine for — and what is it wrong for?
Shops cutting a mixed diet of rigid material: foam PVC, foam board, corrugated and aluminium composite. It is the wrong machine if you only cut roll vinyl — a roll-fed cutting plotter is both far cheaper and faster at that. If you want printing and cutting on one machine, look at the MS-1600 PC print-and-cut instead.
Is three-phase power mandatory?
In practice yes. The machine ships for 3 × 380–400 V + N at a maximum of 20 A. A single-phase variant exists, but most of the load is the vacuum pump and single-phase caps pump capacity. Bringing the panel to the machine and preparing residual-current protection is your responsibility before installation; we walk through it at the pre-install survey.
Does it really cut at 1000 mm/s?
1000 mm/s is peak carriage speed, not average cutting speed. Real throughput follows the length of cut path per square metre: on 30 cm letters the carriage reaches peak speed along the straights, on 3 cm label contours it starts decelerating before acceleration has finished. On small contours the 1 G acceleration matters more than peak speed. Our m²/h figures are for a full bed.
Does the routing module replace a CNC router?
No. The router module is for clean-edged cuts in thin foam PVC, acrylic and aluminium composite; thick timber, deep passes and 2.5D carving are CNC router work. If you intend to route, a dust extraction unit is mandatory and is not included in the price.
Will it work with another brand of printer?
Yes. The cut path is produced in ONYX, Caldera or SAi Flexi; all the machine expects is registration marks placed correctly in the print. Whatever the printer brand, once the mark layout in the RIP output is set up the workflow does not change.
What do the consumables cost?
Blades and the cutting underlay are consumables. Blade life on corrugated and foam PVC is markedly shorter than on adhesive vinyl, and on the oscillating tool a blade change is routine shift work. The underlay also wears by material and is replaced periodically. Budget both as a monthly consumable line, not as a one-off.
05 — SIMILAR